Видео

Can you share which storage building you used?

If I have 5” gutters. How much area do I lose with water entering downspout. In other words, I have roughly a rectangular opening but with this installed I will have a small round opening for the water entering the downspout.

Thank you for the video. Why does the crackling sound without changing the temperature?

those 90s you repaired do not look like they are for pool use Fittings for pool use have 1 3/8 depth for the slip... yours look like 3/4. for house hold plumbing like under the sink

From where you got the top for the washer and dryer?

Would this work for hot tubs?

I am not a professional, but from what I understand, and from the installation instructions that come with the Oatey shower pan liner, the wall (cement board or whatever you use) should be installed before the the drypack?

Quick question how long do you think this took you? I have never done this but am mechanically inclined to do so and it needs done!!

Why did you install your solar tubes in a shaded spot?

i wouldnt stop watering it down

I would have run them in a series rather than as three separate units tied into the same line. This would provide maximum heating while also alowing you to run the pump at full output. Other than that, great job!

The folks that did their driveway, do you happen to know if they did a video?

There is no way you can buy all those fittings at greedy Lowes for $10, no way!

does anyone know how to hook this up for a intex pool hosing? The connectors don't screw on to the intex pool hosing. HELP

Not really shaker doors though are they? No routed frame to add strength ply may warp over time.

I am thinking about using this for my inground pool for a vacuum system. Would you recommend this for what I am trying to do? And does the sand come with it? As a portable system

I like the design. Did you ever do an updated video with higher temp tubing and/or removable polycarbonate roof?

Good video. However, you used your drill as a hammer? I won't bore you with the applicable adage.

I was so excited to find an actual person review this set up before I bought it. Almost 5 hours later, I still do not have a setup that can be used. You have nicely plumbed your setup. So for those of us amateurs... I cannot get a seal at ANY fitting. Even the chinzy hose that came with it from the filter to the pump. My other pump hose connections always had a near-flush gasket at all the fittings. These fittings are relying on just the clamp. The directions (that are horrible with no illustrations) say to put Teflon tape on some spots... did not work. Also the winter drain fitting is a nightmare to get tight enough so it doesn't drip. My husband will be working on fittings tomorrow and I will update comments.

What’s the highest temperature you have been able to reach with this new solar system? Thanks

Literally just trying to figure out where all the harness plugs need to go and this dude absolutely blew past showing where any of the plugs come from or anything with the electrical

The use of non treated wood in contact whit concrete and moist surfaces is a no know mistake, wood expands and rotten over time causing a poor performance and damage of the materials attached Don’t repeat this huge mistake. He works very clean and organized

Hell no

I am not a fan of dry placement of concrete. While it can look as good as wet placement, it is much weaker. I can say that with confidence because I have tested both wet placement and dry placement samples. BTW, high strength concrete has Portland cement in it. Aside from really expensive polymer based concretes, all use Portland cement as a constituent. Another common problem is in the process of misting and flooding, it can wash away some of the fines at the surface so you tend to see more exposed aggregate. For the samples I tested, the surfaces looked almost better than wet placement, but the edges were easier to chip off. But in the compression test the true reality sets in. It broke at half the strength of the wet pour using the same mix design.

The Oatey directions shows the preslope, then pan liner,then the water proof board on wall so that the mortar pan will embed and cover the edge of the wallboard at the base

It would have been much better to use a black asphalt peel and stick roofing material for flat roofs or some metal roofing. That tar paper will break down in the sun and heat in two seasons. But the concept is cool. Just use beer materials, and stain steel fasteners.

What was put on the 2x4's that they came off so easily?

Check valves for controlling flow. Oh... you said it like 30 sec after i posted in the video.

Did you have a video of the noise it was making before?

I wonder if the holes in your roof will leak?

Chris is there anyway i can get in contact with you to talk bout the qr25 motor build need to know bout the second timing chain an what i need to do

I have an 01 same excat van. Mine was overheating and i replaced the water pump and thermostat. I didnt know that bleeding would take that long so was not bled as long as you did. After 2 bottles of blue devil head gasket seal the temp gauge reads fine, but no heat still from heater and the coolant is disappearing. Cant find a leak and replaced water pump gasket. Do i need to bleed the system correctly or could thermostat need to be replaced again? I dont see coolent in oil either. Thanks for any advice and thank you for this video!

Rock Chalk JHawk!!!

Came out nice but did u make the butcher block or buy it

You glossed over the depth of the base of your rock/gravel base. How many inches is it? How thick will the slab end up being?

That hammer is not a good look. Building a house?

I've got some engine rattle in 2nd gear (during steady acceleration, no misfire, hesitation or CEL) on my '05 1.8LS A/T -you reckon that might be a valve clearance issue? I'm consuming/leaking (can't find source) oil pretty good and MPG down a bit. Thoughts? Right on dude, keep motorin'!

I have never used rerods i all ways used fencing wire

Could we get an update comment, still satisfied?

Are the bulbs in your headlights LED?

Ive watched a lot if videos of dry pours and this is the first time ive seen the paint roller method. Looks so good!

Nice

I'm doing a 3' hole a little bit larger than a basketball to put in a flag pole. Would you use rebar in the hole? Can I use the same watering method that you used in this video? Thanks!!!

I had professionals do mine and yours looks better,they used bags but mixed the concrete with a mixer took them 8 days to do a single day job ….and they kept asking for more money for materials…..you get what you pay for

Your water is ~110° and you want a water heater?!

Instead of sifting just buy a bad of straight powder..

Great video. Thanks for the step by step instructions.

there's got to be dry spots in that slab

Axel is missing already on both wheels keep that in mind.

I wanna do this for kids to play basketball on ?? Thoughts